Effect of high intensity ultrasound on gelation properties of silver carp surimi with different salt contents

Surimi from silver carp with different salt contents (0–5%) was obtained treated by high intensity ultrasound (HIU, 100 kHz 91 W·cm⁻²). The gelation properties of samples were evaluated by puncture properties, microstructures, water-holding capacity, dynamic rheological properties and intermolecular interactions. As the salt content increased from 0 to 5%, gel properties of surimi without HIU significantly improved. For samples with low-salt (0–2% NaCl) content, HIU induced obvious enhancement in breaking force and deformation. HIU promoted the protein aggregation linked by SS bonds, hydrophobic interactions and non-disulfide covalent bonds in surimi gels with low-salt content. Moreover, microstructures of HIU surimi gels with low-salt content were more compact than those of the corresponding control samples. HIU also improved the gelation properties of surimi with 3% NaCl to an extent. However, for high-salt (4–5% NaCl) samples, HIU decreased the breaking force and deformation of surimi gels due to the degradation of proteins suggested by increased TCA-soluble peptides. In conclusion, HIU effectively improved the gelation properties of surimi with low-salt content (0–2% NaCl), but was harmful for high-salt (4–5% NaCl) surimi. This might provide the theoretical basis for the production of low-salt surimi gels.     

Synthesis and comparative study on polyetherimides from isomeric 4,4′-isopropylidenediphenoxy bis(phthalic anhydride)s

Two isomers of commercial 4,4′-(4,4′-isopropylidenediphenoxy) bis(phthalic anhydride) (4,4′-BPADA), that is, 3,4′-(4,4′-isopropylidenediphenoxy) bis(phthalic anhydride) (3,4′-BPADA) and 3,3′-(4,4′-isopropylidenediphenoxy) bis(phthalic anhydride) (3,3′-BPADA), were synthesized through aromatic nucleophilic substitution from nitrophthalonitrile and bisphenol A. 3,4′-BPADA was first synthesized from two intermediates, that is, 3-(4-[4-hydroxyphenylisopropylidene] phenoxy) phthalonitrile (3-BPADN) and 3,4′-(4,4′-isopropylidenediphenoxy) bis(phthalonitrile) (3,4′-BPATN). The corresponding three series of polyetherimides (PEIs) were prepared with two representative aromatic diamines (4,4′-oxydianiline and m-phenylenediamine (m-PDA)) via two-step procedure and chemical imidization. Isomeric polyimides showed T_gs from 206 to 256°C in nitrogen and T_d5%s from 488 to 511°C in argon, good mechanical properties (tensile moduli of 2.3–3.3 GPa, tensile strengths of 70–96 MPa, and elongations at break of 3.2%–5.1%), and good solubility. With the introduction of 3-substituted phthalimide unit, PEIs displayed higher T_g values, lower strengths and elongations, better solubility and larger d-spacings. The rheological properties of thermoplastic polyimide resins based on the BPADA isomers were investigated, which showed that polyetherimide PEI-3b derived from 3,3′-BPADA and m-PDA had the lowest melt viscosity among the isomers, indicating that the melt processibility had been greatly improved.     

Study on the Relationship between Emulsion Properties and Interfacial Rheology of Sugar Beet Pectin Modified by Different Enzymes

The contribution of rheological properties and viscoelasticity of the interfacial adsorbed layer to the emulsification mechanism of enzymatic modified sugar beet pectin (SBP) was studied. The component content of each enzymatic modified pectin was lower than that of untreated SBP. Protein and ferulic acid decreased from 5.52% and 1.08% to 0.54% and 0.13%, respectively, resulting in a decrease in thermal stability, apparent viscosity, and molecular weight (Mw). The dynamic interfacial rheological properties showed that the interfacial pressure and modulus (E) decreased significantly with the decrease of functional groups (especially proteins), which also led to the bimodal distribution of particle size. These results indicated that the superior emulsification property of SBP is mainly determined by proteins, followed by ferulic acid, and the existence of other functional groups also promotes the emulsification property of SBP.     

两例相同混合配体构筑的Pb(Ⅱ)/Ag(I)配位聚合物及其荧光性质

多齿配体2-咪唑乙酸(Hima)、4,4'-连吡啶分别与金属盐Pb(NO₃)₂和AgNO₃反应,得到[Pb₂(4,4'-bipy)(ima)(NO₃)₃]_n(1, 3D framework)和[Ag₄(4, 4'-bipy)₃(ima)₂(NO₃)₂(H₂O)₂]_n(2, 3D framework)两个配位聚合物。根据配位聚合物的结构特点,研究了这两个配位聚合物荧光性质等物理化学性能。配位聚合物1在最大激发波长(λ_ex=346 nm)激发下,荧光的最大发射波长为552 nm,配位聚合物2在最大激发波长(λ_ex=369 nm)激发下,荧光的最大发射波长为444 nm。这可能是由于金属和配体之间发生了电荷转移(LMCT)。     

Ni、Mo共掺杂对SnO2材料性能影响的仿真研究

针对AgSnO₂触头材料存在的不足,采用基于密度泛函理论的第一性原理对SnO₂、Ni单掺杂、Mo单掺杂以及Ni-Mo共掺杂SnO₂材料进行了电性能与力学性质的研究,计算了各体系的形成能、能带结构、态密度、弹性常数等各项参数。结果表明,掺杂后的材料可以稳定存在,且仍为直接带隙半导体材料。与未掺杂相比,掺杂后体系的能带结构带隙值减少,其中Ni-Mo共掺杂时的带隙值最小,载流子跃迁所需能量减少,极大地改善了SnO₂的电性能;由弹性常数计算了剪切模量、体积模量、硬度等参数,其中Ni-Mo共掺杂时的硬度大幅降低,韧性增强,有利于AgSnO₂触头材料后续加工成型,且其普适弹性各向异性指数最小,不易形成裂纹。综合各项因素,Ni-Mo共掺杂能够很好地改善SnO₂的性能,为触头材料的发展提供了理论指导。     

基于5-磺基水杨酸的单、双核铜(Ⅱ)三元混配配合物的合成及晶体结构

以5-磺基水杨酸和咪唑衍生物为配体合成了单核、双核结构的三元混配Cu(Ⅱ)配合物:[Cu(H₂biim)(Hssal)(H₂O)₂]·H₂O(1)和{[Cu(MeHbiim)(Hssal)(H₂O)]·0.5H₂O}₂(2)(H₃ssal=5-磺基水杨酸,H₂biim=2,2’-联咪唑,MeHbiim=N-甲基-2,2’-联咪唑),并利用元素分析、红外光谱、紫外-可见光谱、X-射线单晶衍射及热重分析等技术手段对其结构进行了表征。单晶结构解析表明配合物1属于单斜晶系,P2₁／C 空间群,Cu(Ⅱ)离子与1个5-磺基水杨酸根、2个水分子以及1个联咪唑分子形成五配位四角锥构型的单核配合物结构。配合物2属于正交晶系,P2(1)2(1)2(1)空间群,双核Cu(II)离子分别处于五配位四角锥和四配位平面四边形的几何构型的配位环境中,与配合物1不同,5-磺基水杨酸采取μ₂双-单齿配位模式。荧光光谱分析表明配合物2具有较强的荧光性。     

ZnO超细纳米线阵列的制备及其电化学性能

以Zn(NO₃)₂· 6H₂O和C₆H₁₂N₄为原材料,采用二步水热法在碳纤维布上合成了形貌尺寸均匀的ZnO超细纳米线阵列。用 X 射线衍射(XRD)和扫描电镜(SEM)对其晶体结构和形貌进行了表征,利用恒流充放电测试等手段对其进行电化学性能测试。测试结果表明,材料表现出优异的电化学性能。在200 mA/g的电流密度下循环150次后,ZnO超细纳米线阵列仍然约有730 mAh/g的充放电比容量,库伦效率保持在95%以上。在1 200 mA/g的大倍率条件下,材料的充放电比容量依旧可达481 mAh/g左右,表现出十分良好的循环稳定性和可逆性能,是一种较为理想的锂离子电池负极复合材料。     

Synthesis of Heat-resistant Polymers by Thiol–Ene Reaction of N-Allylmaleimide Copolymers Using Glycoluril Crosslinkers with Rigid Molecular Structures

We carried out the thermal curing of the copolymers of N-allylmaleimide (AMI) and 2-ethylhexyl acrylate (2EHA) using 1,3,4,6-tetra(2-mercaproethyl)glycoluril ( G1 ), 1,3,4,6-tetra(3-mercaptopropyl)glycoluril ( G2 ), 1,3,4,6-tetraallylglycoluril ( G3 ), triallylisocyanurate (TAIC), and pentaerythritol tetrakis(3-mercaptobutyrate) (PEMB) as the crosslinkers. Based on the results for the analysis of thiol–ene reactions monitored by IR spectroscopy, it was confirmed that the curing rate significantly depended on the combination of the used crosslinkers. The insoluble fraction after curing was more than 90% for the systems using the glycoluril crosslinkers, while the conversion of the allyl groups was suppressed due to the rigid structure of these crosslinkers. The heat resistance and the mechanical properties of the crosslinked polymers were investigated by thermogravimetric analysis, differential scanning calorimetry, dynamic mechanical analysis, and mechanical tensile tests. For the products cured using the glycoluril crosslinkers, the glass transition temperature (T_g) and the maximum temperature of thermal decomposition (T_max) were 54–59 °C and 395–409 °C, respectively, being higher than those for the cured product prepared with PEMB and TAIC as the conventional crosslinkers. The elasticity (75–139 MPa), the maximum strength (3.0–4.1 MPa), and the adhesion strength (6.7–10.7 MPa) for the polymers cured with the glycoluril crosslinkers, determined by the mechanical tensile and single lap-shear adhesion tests, were higher than those for cured materials produced with PEMB. Thus, the thermal and mechanical properties of the maleimide copolymers were efficiently enhanced by crosslinking using the rigid glycoluril compounds. © 2020 Wiley Periodicals, Inc. J. Polym. Sci. 2020 , 58, 923–931     

Highly stretchable,self-adhesive,and self-healable double network hydrogel based on alginate/polyacrylamide with tunable mechanical properties

A number of synthetic hydrogels suffer from low mechanical strength. Despite of the recent advances in the fabrication of tough hydrogels, it is still a great challenge to simultaneously construct high stretchability, and self-adhesive and self-healing capability in a hydrogel. Herein, a new type of double network hydrogel was prepared based on irreversible cross-linking of polyacrylamide chains and Schiff-base reversible cross-linking between glycidyl methacrylate-grafted ethylenediamine and oxidized sodium alginate (OSA). The combination of both cross-linkings and their synergistic effect provided a novel hydrogel with high strength, stretchable, rapid self-healing, and self-adhesiveness to different material. Besides, the hydrogels with diverse OSA content could maintain their original shapes after loading–unloading tensile test. The resulting hydrogel has a great potential in various fields for supporting and load-bearing substance.     

Relationships between molar mass and fracture properties of segmented urethane and amide copolymers modified by chemical degradation

This publication highlights the structure–property relationships in several thermoplastic elastomers (TPEs): one poly(ether-block-amide) and two thermoplastic polyurethane elastomers with ester and ether soft blocks. Structural changes are induced by chemical degradation from virgin samples through hydrolysis and oxidation. Molar mass measurements show an exclusive chain scission mechanism for all TPEs, regardless of the chemical modification condition. Mechanical behavior was nevertheless obtained from uniaxial tensile testing and fracture testing while considering the essential work of fracture (EWF) concept. During the macromolecular scission process, elongation at break shows a plateau followed by a drop, while stress at break decreases steadily. Once again, the trend is identical for all TPEs in all conditions considered. The βw_p parameter determined using the EWF concept exhibits an interesting sensitivity to scissions (i.e., molar mas decrease). Plotting elongation at break as a function of molar mass reveals a strong correlation between these two parameters. This master curve is particularly remarkable considering the range of TPEs and chemical breakdown pathways considered (hydrolysis and oxidation at several temperatures). Relevant structure–property relationships are proposed, highlighting that molar mass is a predominant parameter for determining the mechanical properties of thermoplastic elastomers.